DT200 Money Counter
-
DT200 - Adjusting the Feeding Gap
The following video will demonstrate how to ensure a trouble-free counting operation: https://youtu.be/mwpRa0gr-mM When the notes are improperly fed into the machine, please adjust the hopper feeding gap by fine-tuning the Thickness Wheel located on the back of the machine. Proceed with this ... -
If you encounter EA0 or EA1 error as soon as you turn on the machine or during the count please follow below instructions on how to resolve the issue. Step 1: Please try cleaning the Counting Sensors with clean dry cloth or a brush The following article will demonstrate how to perform the ...
-
If you encounter EA2 error as soon as you turn on the machine or during the count please follow below instructions on how to resolve the issue. Step 1: Please try cleaning the Stacker Sensors with clean dry cloth or a brush The following article will demonstrate how to perform the Maintenance...
-
If you encounter EA3 error as soon as you turn on the machine or during the count please try cleaning the Speed Sensors with clean dry cloth or a brush Step 1: Open left cover This video will demonstrate how to safely open the machine and ensure the cables are plugged properly https://www.youtub...
-
If you encounter EA4 error as soon as you turn on the machine or during the count please follow below instructions on how to resolve the issue. Step 1: Please try cleaning the Feeding Sensor with clean dry cloth or a brush and make sure nothing is blocking the sensor The following article wil...
-
This video will demonstrate how to safely change the Fuse: https://youtu.be/gpeMl66uTsQ Please ensure the machine is turned on before proceeding with the steps. Use the same type and rating (F2A-250V). The fuses are located in the power jack compartment. Please reach out to support@deteckusa.c...
-
DT200 - How to place the Notes
This video will demonstrate how to properly place the notes on the hopper stage: https://youtu.be/9flEAmnDwRc To ensure a trouble-free operation before starting, please make sure to: 1. Tidy up the notes on an even desk. 2. Set the position of the counting guide to be 2mmto 3mmlonger than the n... -
DT200 - How to remove stuck notes from the Hopper Stage
This video will demonstrate how to safely remove Notes stuck in the Hopper stage: https://youtu.be/de9vhWToXGs Please ensure the machine is turned off before proceeding with the steps. 1. Loosen the Wheel by turning it counter-clockwise, towards the "-" sign 2. Gently spin the hopper wheels upwa... -
DT200 - How to replace the rubber belt
This video will demonstrate how to replace the rubber belt https://youtu.be/fGUq_tgZAoU Please ensure the machine is turned off and the power plug is removed from the power socket before proceeding with the troubleshooting steps. -
DT200 - How to replace the rubber tongue
This video will demonstrate how to replace the rubber tongue https://youtu.be/-7-EvFLypFo If you experience repetitive errors over time, you will most probably have to change the worn rubber tongue with a new one. Below step by step demonstrates how to do so: Please ensure the machine is turne... -
DT200 - How to resolve common counting errors
In case the machine is not having an accurate counting operation and you're getting the following E - Error codes (EA0, EA1, EA2, EA3, EA4), proceed as follow: Ensure that the notes are placed orderly in the hopper. Check the counting sensors for dust or any other kind of malfunctioning source. ... -
DT200 - How to resolve counterfeit detection alerts
Please follow below troubleshooting steps to resolve repetitive counterfeit errors: If the issue is still not resolved, please contact support@deteckusa.com so we can advise on how to reduce sensor sensitivities. Press and hold the ADD button for 3 seconds. Press the Batch button to change Se... -
DT200 - How to setup the printer
This video will demonstrate how to adjust the settings to print mode: https://youtu.be/E5KKhR8NBT8 The DT-200 is compatible only with DETECK Printers. You can connect the printer through the LAN Port located on the back of the machine. Once you turn On the machine, please ensure the LAN Port i... -
DT200 - How to use the Single Value Count Mode
This video will help demonstrate how to use the Single Value Count Mode: https://youtu.be/7FhlCdft5Fw Value Count Mode To access this mode, 1. a, Press CUR Button to select a currency and to access Value Count Mode b, Press the VAL Button for 3-5 seconds until the VAL indicator is on. 2. Se... -
DT200 - Machine Not Turning On
Please check the fuse compartment. Press on below article which will help demonstrate how to check and replace a damaged fuse Article Name: DT200 - Fuse Replacement Article Link: https://deteckusa.reamaze.com/articles/dt200-fuse-replacement If this doesn’t help resolve the problem, please conta... -
Following these periodic cleaning routines will help to keep the machine in the optimum condition for ensuring a trouble-free operation as well as to extend the machine’s lifespan. https://youtu.be/3PF_jcz9wJc DAILY ROUTINE: Perform the following steps on a daily basis: 1. Turn Off the machine ...
-
If you are experiencing issues with the motor and rotators not working, please follow the steps below: A. You can hear the sound of the main motor turning Step 1: Open right cover This video will demonstrate how to safely open the machine and ensure the cables are plugged properly https://yout...
-
We recommend watching this tutorial video in order to make the best use of this product. https://youtu.be/Yse2GD_wIfE Please follow below step-by-step instructions: 1. Place the machine on a solid flat surface before using. 2. Please review the safety considerations to carefully choose an appro...